Tag Archives: support spindles

Looking for the top twelve – two contenders

On this latest spin I used two spindles – a new-to-me Mirkwood – destashed by one of the best spindle enablers in our guild; and a Takhli style from The Spindle Shop. I’ll give my feedback one by one.

Mirkwood: (49g and 26cm long) it’s a lovely spindle and I would never have bought it if I just looked at it online. It looked very bottom heavy (which it is) and didn’t have a thin shaft, instead has a crystal at the top! It also has crystals around the bottom rim.

I was smitten from the first flick – the red crystals mesmerize and delight me. It has a ball bearing at the bottom tip which makes for a long and nearly friction-less spin. I use a wooden spinning bowl with it because I don’t like the sound of the ball bearing against my glass and ceramic bowls. In a Tibetan-style, it has a something to build your cop against. The shaft is smooth and slightly shaped to helped with cop building.

There is no sharp point on the end of the spindle. As noted, it has a ball bearing. My only frustration with this spindle is that the lack of point on the end makes it just that little bit more difficult to brace it against my thigh or waist to wind on a firm cop. Despite that, and largely for the crystals and weight, this spindle is in the running for my “top 12”.

The other spindle I used on this spin is a Takhli style (17g and 21cm long) by The Spindle Shop in Queensland, Australia, along with their spinning bowl. It’s light, short, and spins above its weight. Smooth shaft with a rim on the bottom, it is easy to build a stable cop on this spindle. From the first flick of this spindle, I knew it would make it to the top 12. And yes, it’s there too.

It is important to note my spinning style and practices. I mostly (nearly always) spin while in bed. I know that sounds odd, but I choose my support spindles for spinning as part of a meditative practice. Something to focus me in the morning (15 minutes) and again in the evening as I settle in for sleep. It is within this context that I judged/assessed these spindles for my use.

I prepared the fibre (polwarth/silk 70/30 or 80/20 – can’t recall) into light rolags using my blending board. My focus was on experimenting with each spindle – so for that I chose light rolags with silk and a fine wool. As I filled each spindle, I wound it onto a plying ball, splicing the yarn so it was one continuous thread. You can see it in the top right corner of the first photo. Once all the fibre had been spun, I had a fairly large (53g) ball of singles yarn. Using my ball winder, I wound it into a centre pull ball, and from that wound a two-strand plying ball.

I know that seems like a lot of work, but I have learned that making a two-strand plying ball prior to plying leads to a pleasant experience plying. When you get to the near end of the centre pull ball, sometimes (nearly EVERY time) the middle collapses and you need to untangle it. It happened this time and I ended up losing the last couple of grams of spun yarn. 🙁

It’s easier to untangle the mess if you are just winding a ball, and not when you are managing the twist on a wheel (or spindle) in motion.

I plied the yarn on my wheel (Majacraft Rose) and put extra ply twist into it. The result is a 177m of yarn – washed and ready to go.

Summary: both spindles are a delight to use. And I learned not to judge a spindle just by the look – argh! That means I have to try them all out? I’m doomed . I like that they are on the shorter side (26 cm or less) and have smooth shafts to build a cop on. I also love that they each have a bit of a base to build the cop against. Cop management is a big thing as a firm cop helps to keep the spinning going.

Stay tuned as I go through my collection and (try to) rank it to a top 12.

Before and after – full spindles, naked spindles

One of the things I like to do when I am spinning on spindles, is to select a bunch of them to explore. I have a strong desire to learn as much about support spindles as I can, and my spinning time is limited. At this stage of my spinning journey with these new (to me) tools, I am not overly fussy about the yarn, so I will happily combine support and suspended spindles into my explorations.

In the photo below, there are three cross-piece (suspended) spindles AKA Turkish spindles along the top; and in the next row a suspended spindle by Eric Stapleton; and support spindles by Texas Jeans, CreativeJayne (the next two); can’t remember the maker of the dark wood Phang; and the last one is by Carry Cherry. The last four spindles I purchased online, only viewing photos and hoping for the best. These did not disappoint. They are a variety of weights and shapes. I move from one spindle to the next as determined by my attention span, temperament, and interest in the task at hand.

The fibre I’m spinning is mostly wool with some silk/yak made into rolags on my blending board.

I will spin on one spindle for a day or so, and then switch to another one. And so on. Doing this allows me to compare the spindles, the amount of energy it takes to get the spindle into motion, the amount of time it holds a spin (or doesn’t); and how the weight feels and affects my hands. When my hands, mostly my right thumb, gets sore, I stop. I take a break, wash the dishes – warm water helps soothe the sore muscle. And then a few hours or days later depending on how sore my thumb is, I start again with a different spindle.

With each spindle I am learning new things; new strategies for winding a cop or turtle; new techniques for keeping the spindle in motion; and with the support spindles, I am also exploring the different styles and materials used in the spinning bowls. It really is a rabbit hole of things to explore; spindles, fibre preps, spinning bowls, and then of course, techniques.

In the photo below I show (all but cross-piece) spindles without the yarn on them, so you can see their shape. I wouldn’t say that each spindle was full – but they were mostly full enough for me. As you make and store the yarn onto your spindle, it adds weight to the spindle. The process of winding the newly spun yarn onto the spindle is called building your cop. The cop is the name of the stored yarn. Even that part of the process takes skill and decision making.

So with each spindle I’m learning, reflecting, and mostly enjoying the process of making yarn with a stick. Working with several at a time gives me a chance to do instant comparisons and over time, I’ve learned what my favourite shapes, weights, and lengths are.

More to come about that.